超便攜式帶電低壓電網電纜識別器
電力公司及其承包商在某些作業情況下,需要識別仍處於帶電狀態的電纜,例如打開電纜溝、施作分支電路,以及配電網維護作業前後等。由於誤選電纜可能造成嚴重後果(例如危及人員生命安全、導致電網故障等),因此必須快速且明確地完成電纜識別。
Merytronic 開發了 IC2G 超便攜式電纜識別器,專門用於低壓配電電纜的精確識別。
本設備由發射器 (IC2G-TX) 及接收器 (IC2G-RX) 組成,操作簡便:將發射器 (TX) 連接至低壓配電電纜,再使用接收器 (RX) 沿電纜往上游方向、朝中壓/低壓變壓器的方向,識別或定位該電纜。
顯示器會顯示訊號注入點的電壓 (TX)、電流 (RX)、接收訊號的極性 (RX)、電池資訊 (TX & RX)。
主要特點
- 無須將線路停電,即可精確識別電纜
- 適用於最高 250 VAC (50–60 Hz) 的低壓配電電纜
- 配備兩種不同的感測器:
- 環形感測器:將環形感測器套在電纜周圍,以識別電纜;適用於單相電纜。
- U 型感測器:透過接觸電纜來識別導體;適用於單相及三相電纜。
- 識別演算法持續運作,可在數秒內完成精確識別。
- 發射器與接收器會自動同步,操作簡便。
T 型感測器:用於電纜路徑預定位
在低壓電網的維護作業中,有時需要確認電力電纜的鋪設路徑。
Merytronic 開發了一套解決方案,只需將 T 型感測器連接至 IC2G 設備,即可快速、簡便地預先定位仍處於帶電狀態的電纜路徑,無須中斷電力供應。
- 適用於帶電的低壓電網。
- 無須切斷電源,即可預先定位電纜路徑。
- 可從任何檢修點進行定位。
T 型感測器︰預先定位帶電低壓電纜
操作示意圖

Ariadna IC2G-TX Transmitter
|
尺寸 (mm) |
120 × 220 × 65 |
|
重量 |
0.75 kg |
|
防護等級 |
IP54 |
|
工作電壓 |
100-250 Vac (50/60Hz) |
|
最大連接電壓 |
480 Vac (50/60Hz) |
|
電源 |
4 × 1.5V 3號電池 |
|
輸出電流 |
峰值 70 A |
|
電纜長度 |
180 cm |
|
短路保護 |
6A 10×38 mm保險絲 |
|
操作溫度 |
-10 / 55 ºC |
Ariadna IC2G-RX Receiver
|
尺寸 (mm) |
120 × 220 × 65 |
|
重量 |
0.75 kg |
|
防護等級 |
IP54 |
|
最大被動電流 |
250 A (50/60Hz) |
|
識別提示方式 |
聲音及螢幕視覺提示 |
|
電源 |
4 × 1.5V 3號電池 |
|
感測器 |
羅氏線圈及 U 型感測器 |
|
操作溫度 |
-10 / 55 ºC |
品質標準
Ariadna IC2G 符合歐盟低電壓指令72/23/EEC及EN 61010-1(電子量測、控制及實驗室用設備的安全要求)
There are many situations in which it is necessary to quickly and accurately identify live Low Voltage (LV) cables, for example, when opening a trench, making a branch in a line, before carrying out some maintenance tasks, when making a new connection, …
Merytronic has developed the Ariadna IC2G, an ultra-portable Cable identifier device which is used for positive cable identification, in Low Voltage cables.
The device consists of a transmitter (IC2G-TX) and a receiver (IC2G-RX). Its use is simple: the transmitter (TX) is connected to an LV cable and the receiver (RX) is used to identify or locate that cable upstream, towards the MV/LV transformer.
Main features:
- Positive cable identification without de-energizing the line
- Works on LV distribution cables up to 250 Vac (50-60 Hz)
- Two different sensors:
- Sensor Ring: Identifies cables by placing a sensor ring around the cable (single-phase cables)
- “U” sensor: Identifies conductors by touching the cable (single-phase and three-phase cables)
- The identification algorithm works continuously, and positive identification is achieved in seconds
- Easy to use due to automatic synchronization between transmitter and receiver
T SENSOR FOR pre-location of the cable
In maintenance tasks in LV networks, it may be necessary to know the route of electric cables.
Merytronic has developed a solution that allows a pre-location of the cable route with voltage upstream, in a quick and easy way, by simply connecting a T-sensor to the IC2G device.
- In Low Voltage Active networks
- Pre-location of the cable without cutting the power supply
- From any register point
T Sensor: Pre-location of energised Low Voltage cable
Working diagram

Ariadna IC2G-TX Transmitter
|
Size (mm) |
120 × 220 × 65 |
|
Weight |
0.75 kg |
|
Protection degree |
IP54 |
|
V working |
100-250 Vac (50/60Hz) |
|
V connection max. |
480 Vac (50/60Hz) |
|
Power supply |
4×1.5V AA batteries |
|
Output current |
70 A peak |
|
Cable length |
180 cm |
|
S.C. protection |
6A 10×38 mm fuse |
|
Operating Temperature |
-10 / 55 ºC |
Ariadna IC2G-RX Receiver
|
Size (mm) |
120 × 220 × 65 |
|
Weight |
0.75 kg |
|
Protection degree |
IP54 |
|
Max. passive current |
250 A (50/60Hz) |
|
Identification indication |
Acoustic and visual (display) |
|
Power supply |
4×1.5V AA batteries |
|
Sensors |
Rogowski and U sensor |
|
Operating Temperature |
-10 / 55 ºC |
Quality standards
Ariadna IC2G is compliant with EU Low Voltage Directive 72/23/EEC and EN 61010-1 (Safety requirements for electronic equipment for measurement, control and laboratory use)